Nissan Qashqai (2013-2017) Fuse Diagram • FuseCheck.com (2024)

Advertisem*nts

Fuse box diagram (fuse layout), location, and assignment of fuses and relays Nissan Qashqai (J11) (2013, 2014, 2015, 2016, 2017).

Checking and Replacing Fuses

Fuses and fusible links protect your vehicle’s electrical system from short-circuiting or overloading. If electrical parts in your vehicle are not working, the system may have been overloaded causing a blown fuse. Before you replace or repair any electrical parts, check the appropriate fuses.

Be sure the ignition switch is pushed to the OFF or LOCK position and all switch are OFF.
Open the fuse box cover.
On the fuse diagram, find the number of the fuse you want to check. The diagram tells you where to locate the fuse on the panel. Pinch the fuse perpendicularly with the fuse puller and pull it out.
To check a fuse, look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse with a new one.
If a new fuse also opens, have the electrical system checked and repaired by a Nissan dealer or a repair facility of your choice.

Notice

Never use a fuse of a higher or lower amperage rating than that specified. This could damage the electrical system or cause a fire.
Never replace a broken fuse with anything other than a new fuse (such as wire, foil, etc). Use always an intact fuse of the same color.

Instrument Panel Fuse Box #1

The fuse panel is located behind the lid on the left side of the instrument panel. The fuse puller (1) is stored in the fuse box.

Back-side:

№	A	Circuit Protected
1	15	Combination Switch, Pump Control Unit, Washer Switching Solenoid Valve
2	10	Air Bag Diagnosis Sensor Unit
3	5	Combination Meter
4	10	Sonar Control Unit, PTC Relay 1, PTC Relay 2, PTC Relay 3, Front Camera Unit, Illumination, Audio, Fuel Heater Relay, Data Link Connector, Stop Lamp Switch, Distance Sensor, Auto Anti-dazzling Inside Mirror, EPS Control Unit, Combination Switch (Spiral Cable), Chassis Control Module, Auto Anti-dazzling Inside Mirror, 4WD Control Unit, Electric Park Brake Control Unit, Around View Monitor Control Unit, Steering Angle Sensor, Navi Control Unit
5	10	DC/DC Converter
6	15	Front Heated Seat Switch
7	20	Blower Motor, Air Conditioner Amplifier, Engine Restart Baypass Control Relay
8	5	Stop Lamp LH, Tail Lamp LH, License Plate Lamps, Glove Box Lamp, Headlamp Aiming Switch, Audio, Navi Control Unit
9	-	-
10	15	Rear Window Defogger
11	15	Rear Window Defogger
12	10	Door Mirror Heater
13	10	ABS
14	10	Air Conditioner Control, Air Conditioner Amplifier, Sunshade Motor Assembly, Brake Pedal Position Switch, Stop Lamp Switch, Door Mirror Remote Control Switch
15	15	1.2L HR with CVT, 1.6L MR16DDT, R9M (Euro3):Interior Room Lamp Relay
15	20	except ↑:Interior Room Lamp Relay
16	-	-
17	20	Blower Motor, Power Transistor, Air Conditioner Amplifier
18	-	-
19	20	Audio, Navi Control Unit, Around View Monitor Control Unit
20	5	BCM (Body Control Module), Siren Control Unit, Sensor Cancel Switch, Combination Switch
21	10	Combination Meter
22	10	Interior Room Lamp Relay
23	-	-
24	10	Stop Lamp Switch, BCM (Body Control Module)
25	5	4WD Control Unit, NATS Antenna Amplifier
26	5	Clutch Interlock Switch
27	10	BCM (Body Control Module), Combination Switch
28	10	Electric Park Brake Switch, Data Link Connector, 4WD Control Unit, Illumination, Power Window Relay, Door Mirror Open Relay, Door Mirror Close Relay
29	20	1.2L HR with CVT, 1.6L MR16DDT, R9M (Euro3):BCM (Body Control Module)
29	15	except ↑:BCM (Body Control Module)
30	15	BCM (Body Control Module)
31	20	1.2L HR with CVT, 1.6L MR16DDT, R9M (Euro3):BCM (Body Control Module)
31	15	except ↑:BCM (Body Control Module)
32	15	1.2L HR with CVT, 1.6L MR16DDT, R9M (Euro3):Power Socket
32	20	except ↑:Power Socket
33	15	1.2L HR with CVT, 1.6L MR16DDT, R9M (Euro3):f
33	10	except ↑:d
Relay
R1	Ignition
R2	Rear Window Defogger
R3	Accessory
R4	Front Blower

Advertisem*nts

Instrument Panel Fuse Box #2

The fuse panel is located behind the lid on the right side of the instrument panel.

№	A	Circuit Protected
71	10	Steering Angle Sensor
72	10	Combination Meter
73	10	Audio, Navi Control Unit, Around View Monitor Control Unit
74	10	Transmission Control Module (TCM), Primary Speed Sensor, Transmission Range Switch, Input Speed Sensor, Output Speed Sensor, Secondary Speed Sensor
75	-	-
76	10	Air Conditioner Control, Air Conditioner Amplifier
77	10	ABS
78	-	-
79	10	Electric Oil Pump Relay
80	20	Audio, Navi Control Unit, Around View Monitor Control Unit
81	10	Transmission Control Module (TCM)
Relay
R1	Accessory
R2	Ignition
R3	-

Additional Fuse Holder

№	A	Circuit Protected
82	10	Electric Oil Pump Relay
83	10	Transmission Control Module (TCM)
84	-	-
85	-	-

Engine Compartment

Open the bonnet, remove the air duct, and remove the fuse box covers.

AIR DUCT REMOVAL

Remove the clips.
Remove the bolt.
Push the top of the retaining clips together to release the air duct.
Slide the air duct towards the front of the vehicle to remove it.

Install the air duct in the reverse order of removal.

Advertisem*nts

Engine Compartment Fuse Box #1 Diagram (IPDM)

№	A	Circuit Protected
51	10	Active Grille Shutter, Engine Control Module
52	15	Engine Control Module, EVAP Canister Purge Volume Control Solenoid Valve, Engine Coolant Bypass Valve Control Solenoid Valve, Fuel Heater and Water in Fuel Level Sensor, High Pressure Fuel Pump, Condenser, Ignition Coils, Exhaust Valve Timing Control Solenoid Valve, Intake Valve Timing Control Solenoid Valve, Fuel Injector Relay, High Pressure Fuel Pump Relay, Mass Air Flow Sensor, Heated Oxygen Sensor, Turbocharger Waste Gate Control Solenoid Valve, Air Fuel Ratio Sensor, Fuel Flow Actuator, Turbocharger Boost Control Solenoid Valve, Intake Valve Timing Intermediate Solenoid Valve, Intake Valve Timing Control Solenoid Valve, Turbocharger Bypass Control Valve, Engine Oil Pressure Control Solenoid Valve
53	15	MR:Throttle Control Motor Relay
54	10	Engine Control Module, Engine Coolant Bypass Valve Control Solenoid Valve, Intake Valve Timing Control Solenoid Valve, Engine Oil Pressure Control Solenoid Valve, Exhaust Valve Timing Control Solenoid Valve, Turbocharger Bypass Valve Control Solenoid Valve, Intake Manifold Runner Control Valve
55	15	Engine Control Module, Heated Oxygen Sensor, Thermostat Heater Control Solenoid Valve, Glow Control Unit, Turbocharger Boost Control Solenoid, Air Fuel Ratio Sensor, Fuel Flow Actuator, Intake Manifold Runner Control Valve
56	15	Engine Control Module, Steering Lock Unit
57	15	Air Conditioner Relay
58	10	Engine Control Module, Engine Restart Relay
59	-	-
60	30	Front Wiper Hi/Lo Relay
61	20	Fuel Pump Relay
62	-	-
63	10	Transmission Control Module (TCM), Primary Speed Sensor, Output Speed Sensor, Transmission Range Switch, Input Speed Sensor, Ipdm E/R, Secondary Speed Sensor
64	-	-
65	5	Engine Control Module, Steering Lock Unit
66	-	-
67	10	Headlamp Aiming Motor, Compressor, Transmission Range Switch, Front Window Defogger RH Relay, Front Window Defogger LH Relay, Reverse / Neutral Position Switch, Back-Up Lamp Switch, Neutral Position Switch

Engine Compartment Fuse Box #2 Diagram

№	A	Circuit Protected
34	15	Horn Relay
35	30	Diesel:PTC Relay 2
36	30	Diesel:PTC Relay 3
37	30	Diesel:PTC Relay 1
38	30	Electric Park Brake Control Unit
39	30	Option Connector
40	-	-
41	30	Electric Park Brake Control Unit
F	50	ESP Control Unit
G	30	ABS
H	50	ESP Control Unit
I	30	Headlamp Washer Relay
J	-	-
K	40	ABS
L	30	Starter Relay, Ignition Relay (Fuse: "1", "2", "3", "4", "10", "11", "12")
M	50	Power Window Relay, Power Window Main Switch, Sunshade Motor Assembly, Power Seat Switch
Relay
R1	Horn

Advertisem*nts

Engine Compartment Fuse Box #3 Diagram

№	A	Circuit Protected
42	10	Gasoline:Transmission Control Module (TCM)
43	-	-
44	10	MR:High Pressure Fuel Pump Relay
44	20	Diesel:Fuel Heater Relay
45	10	MR:Fuel Injector Relay
46	15	MR:Fuel Injector Relay
47	-	-
48	-	-
R	60	Cooling Fan Relay 2
S	30	Engine Control Module Relay (Fuse: "51", "52", "54", "55"), Fuse: "53"
T	30	IPDM E/R, Cooling Fan Relay 1
Relay
R1	Starter
R2	Engine Restart
R3	Diesel:Fuel Heater
R3	MR:High Pressure Fuel Pump

Fuse Holder #1

№	A	Circuit Protected
N	30	DC / DC Converter
O	30	DC / DC Converter

Fuse Holder #2

№	A	Circuit Protected
P	40	Front Window Defogger RH Relay
Q	40	Front Window Defogger LH Relay

Fusible Link Block

It is located on the positive battery terminal.

№	A	Circuit Protected
A	450	Starter, Engine Restart Baypass Relay
B	450	Generator
C	100	Accessory Relay (Fuse: "13", "14", "15"), Rear Window Defogger (Fuse: "10", "11", "12"), Blower Relay (Fuse: "7", "17"), Front Wiper Relay, Headlamp RH, Tail Lamp RH, Stop Lamp RH, Fog Lamp RH, Fuse: "19", "20", "21", "22", "24", "25", "26", "27", "28", "29", "30", "31", "32", "33", "57", "58", "U"
D	100	Ignition Relay (Fuse: "56", "61", "63", "65", "67"), Air Conditioner Relay, Cooling Fan Relay 1, Headlamp LH, Tail Lamp LH, Stop Lamp LH, Fog Lamp LH, Fuse: "P", "Q"
E	50	Fuse: "R", "S", "T", "42", "44", "45", "46"
U	100	Headlamp RH, Tail Lamp RH, Stop Lamp RH, Fog Lamp RH, Thermo Plunger Control Unit, Glow Control Unit, Fuse: "58"
V	100	Fuse: "F", "G", "H", "I", "K", "L", "M", "34", "35", "36", "37", "38", "39", "41", "N", "O",

Advertisem*nts

Nissan Qashqai (2013-2017) Fuse Diagram • FuseCheck.com (2024)

FAQs

How to change the fuse in a Nissan Qashqai? ›

10.16. 2. Engine compartment

Make sure the ignition is OFF and the headlight switch is in the “OFF” position.
Open the bonnet. ...
Remove the fusible link covers.
Locate the fuse that needs to be replaced.
Remove the fuse with the fuse puller (where fitted). ...
If the fuse is open (A), replace it with a new fuse (B).

More items...

What fuse is the parking light on a Nissan Qashqai? ›

Both parking lights run from one fuse (#49), a 10A located in the IPDM (Intelligent Power Distribution Module) under the bonnet.

Read The Full Story ›

Where can I find fuse diagram for my car? ›

To locate the fuse specification chart for your vehicle or to learn how to change a fuse, refer to the "Fuses" section of your Owner's Manual.

Where is the fuse interior fuse box? ›

Usually, you will find two fuse boxes in the car. One is located under the hood and the other is found in the dashboard or near the steering wheel.

Tell Me More ›

Can I replace a fuse by myself? ›

The good news is a blown fuse is pretty easy to replace. Sometimes you may find that a fuse has blown in the plug of an appliance, rather than in your fuse box. This is often caused by an electrical fault in an old or damaged device. Again, changing the fuse is relatively straightforward.

How do I know what fuses my car needs? ›

The most straightforward is to inspect the fuse itself, where the amperage rating is typically noted on or near the top of the fuse. The second is to check the fuse diagram in the vehicle, to understand which fuse type is in each slot.

Read On ›

Where is the secondary fuse box? ›

Locating the Fuse Box

In most cases, the main fuse box is situated under the hood, near the battery, while secondary panels can be found in the passenger compartment, often hidden behind a removable panel.

Know More ›

What is the main fuse in a fuse box? ›

Your fuse box will have two sets of fuses. At the bottom will be 15-amp and 20-amp screw-in fuses with glass faces that are exposed and visible. These fuses will service branch light circuits and outlet circuits. At the top will be 30-amp or 40-amp cartridge main fuses for ovens, laundry rooms, or stoves.

How much does it cost to replace a fuse box in a car? ›

Fuse Box Replacement Labor Cost

it usually takes 4 to 8 hours to replace a fuse box, so average total labor costs usually fall between $320 and $960. Book services and compare quotes from highly rated pros near you.

Discover More Details ›

How do you change a fuse step by step? ›

Replacing a Fuse in a Fuse Box, Step-by-Step

Turn off all electrical devices in the affected area of your home. ...
Turn off the power at the fuse box. ...
Find the blown fuse. ...
Remove the blown fuse. ...
Screw in the fuse in the same location.
Restore power to the fuse box by flipping the main power switch.

Jan 23, 2023

Learn More ›

How do I know if my car fuse is out? ›

Still gripping it with the puller, hold the fuse up to the light (or a light source) and look through the translucent bodywork. You should see a thin metal wire in there. If the wire is no longer a continuous thread and appears broken or in two pieces, the fuse has indeed 'blown'.

Explore More ›